Author Topic: Need firmware for intempo gx01  (Read 3591 times)

gustavw

  • Newbie
  • *
  • Posts: 5
Need firmware for intempo gx01
« on: 01:22:44 | 10 January, 2015 »
Hello, im New in this Board. I have an Intempo gx01.
I habe bricked it by flashing  a firmware.
Can anybody give me a "Reciva firmware set".
I want to flash it with sharpflash.
Sorry for my bad english.

drgeoff

  • Hero Member
  • *****
  • Posts: 853
  • Thanked: 32 times
Re: Need firmware for intempo gx01
« Reply #1 on: 05:47:50 | 11 January, 2015 »
PM sent.

drgeoff

  • Hero Member
  • *****
  • Posts: 853
  • Thanked: 32 times
Re: Need firmware for intempo gx01
« Reply #2 on: 14:14:57 | 12 January, 2015 »
Please continue on the open forum.  Perhaps others can help too.  You wrote:

"I flashed the Firmware.
After this i bootet the Radio, but it shows only Starting, and after a few seconds the Radio restarts, and so on.
The led on the barracuda board flashes continously.
Tryed Factory reset, but it Would Not help.
Do You have any idea,what i can do?"

-----

Is the factory reset doing anything - does it start to happen?  Power disconnected, press and hold 'Select' on the radio, plug in the power, keep 'Select' pressed until message on display.

I can only suggest you flash the firmware again, making sure that all the commands are entered absolutely correctly.

If not working after that, you probably have a hardware fault on the Barracuda module.  I have encountered a few faulty modules but have had no success in making a permanent repair.  Sometimes using freezer spray or hot air from a hair dryer on the module immediately before powering on can make it boot and run OK for a short time.  If that happens you certainly have a hardware fault on the module.

gustavw

  • Newbie
  • *
  • Posts: 5
Re: Need firmware for intempo gx01
« Reply #3 on: 06:01:17 | 13 January, 2015 »
Yes, facto reset works.
I tryed and i Put the wifi Stick in the Front usb it boots, and recognices the stick.
In Network settings it shows the right Mac adress.
If I scan for Networks it sys nö networks.
on the usb Inside the Radio the stick does Not work.

drgeoff

  • Hero Member
  • *****
  • Posts: 853
  • Thanked: 32 times
Re: Need firmware for intempo gx01
« Reply #4 on: 07:27:01 | 13 January, 2015 »
The Intempo GX-01 can connect by ethernet. Have you tried that?

gustavw

  • Newbie
  • *
  • Posts: 5
Re: Need firmware for intempo gx01
« Reply #5 on: 12:22:55 | 13 January, 2015 »
Yes, i have tried, but it won't work. It says no Internet connection.
Could it be the Hardware is a bit different between my Radio and yours?

drgeoff

  • Hero Member
  • *****
  • Posts: 853
  • Thanked: 32 times
Re: Need firmware for intempo gx01
« Reply #6 on: 15:03:05 | 13 January, 2015 »
Yes, i have tried, but it won't work. It says no Internet connection.
Could it be the Hardware is a bit different between my Radio and yours?
Yes the hardware is different but the firmware contains configuration files for every model of radio.  Some precision resistors on the motherboard feed two or three voltages to the module.  The module converts those to a number which tell the module which configuration file to use.

If you go to Settings, Version, Product Code what number do you see?  Should be 761 or 985 depending on which version of the GX-01 you have.  Table at http://www.sharpfin.org/index.php?title=Radios.

gustavw

  • Newbie
  • *
  • Posts: 5
Re: Need firmware for intempo gx01
« Reply #7 on: 10:56:01 | 14 January, 2015 »
Yes it says 761.

drgeoff

  • Hero Member
  • *****
  • Posts: 853
  • Thanked: 32 times
Re: Need firmware for intempo gx01
« Reply #8 on: 14:18:41 | 14 January, 2015 »
If you go to Settings, Network Config, View Config, Network Device what does it say for Wired Device and Wireless Device.
« Last Edit: 14:55:07 | 14 January, 2015 by drgeoff »

gustavw

  • Newbie
  • *
  • Posts: 5
Re: Need firmware for intempo gx01
« Reply #9 on: 23:43:46 | 15 January, 2015 »
I found the Problem. There were 2 wires broken on a connector of the board whitch contains the front usb.
Everything works fine. Thank You for your Help.

 

anything